当前位置：首页 > news >正文

网站开发视频下载网络营销课程介绍

news 2025/7/4 11:38:30

网站开发视频下载,网络营销课程介绍,做网站是需要多少钱,建设路小学家校互动平台网站格式说明 RTL8192cd 驱动程序提供 MIB 接口，可通过“iwpriv”命令获取/设置参数。 set_mib iwpriv set_mib namevalue1[,value2,value3…]” Iface: “wlan0” value: 1.值可以是单个字段，也可以是用“，”分隔的多个字段，字…

格式说明

RTL8192cd 驱动程序提供 MIB 接口，可通过“iwpriv”命令获取/设置参数。

set_mib

iwpriv set_mib name=value1[,value2,value3…]”

Iface: “wlan0”

value:

1.值可以是单个字段，也可以是用“，”分隔的多个字段，字段之间没有任何空格

2.如果值是字节数组的类型，则值的格式将是 0~f 的 ASCII 字符串，其中使用 2 ASCII 代表一个字节。

例如，设置WiFi path A的CCK的TXPower

iwpriv wlan0 set_mib pwrlevelCCK_A=08080909090a0a0a0a0b0b0b0c0c

说明：后面表示1~14信道的功率索引值，08表示信道1的

get_mib

iwpriv get_mib name

Iface: “wlan0”

Channel

获取channel

指令

iwpriv wlan0 get_mib channel

5G

# iwpriv wlan0 get_mib channel
wlan0 get_mib:40

2.4G

# iwpriv wlan1 get_mib channel
wlan1 get_mib:11

channel

2.4G指令

iwpriv wlan1 set_mib channel=1

设置之后读取
/# iwpriv wlan1 get_mib channel
wlan1 get_mib:1

注意：

此时只是设置到mib区了，并未实际生效，要生效需要将接口down up下，指令如下

ifconfig wlan1 down up

信道范围·1~14

5G指令

iwpriv wlan0 set_mib channel=36

设置之后读取

iwpriv wlan0 get_mib channel
wlan0 get_mib:36

信道范围36~165

ch_low/ch_hi

自动信道选择允许选择的最低信道和最高信道,默认值为0表示不限制

获取2.4G默认值

iwpriv wlan1 get_mib ch_low
wlan1 get_mib:0 0 0 0
iwpriv wlan1 get_mib ch_hi
wlan1 get_mib:0 0 0 0

设置2.4G

iwpriv wlan1 set_mib ch_low=1

iwpriv wlan1 set_mib ch_hi=1

备注：

为了测试方便，我们将自动选择限制为1信道，方便查看指令是否生效

设置之后测试

ifconfig wlan1 down up

查看获取信道为1

获取5G默认值

iwpriv wlan0 get_mib ch_low
wlan0 get_mib:0 0 0 0
iwpriv wlan0 get_mib ch_hi
wlan0 get_mib:0 0 0 0

设置5G

iwpriv wlan0 set_mib ch_low=36

iwpriv wlan0 set_mib ch_hi=36

设置之后测试

ifconfig wlan0 down up

查看获取信道为36

preamble

CCK preamble 类型 0: long preamble 1:short preamble

获取指令

iwpriv wlan1 get_mib preamble
wlan1 get_mib:1 0 0 0

设置指令

iwpriv wlan1 set_mib preamble=1

ifconfig wlan1 down up

disable_ch14_ofdm

禁用通道 14 中的 OFDM 发送和接收。它还将阻止自动通道选择 ch14。

value=0 表示disable

value=1 表示enable

获取指令

iwpriv wlan1 get_mib disable_ch14_ofdm
wlan1 get_mib:0 0 0 0

设置指令

iwpriv wlan1 set_mib disable_ch14_ofdm=1

ifconfig wlan1 down up

disable_ch1213

禁止自动信道选择到ch12 和ch13

0:enable

1:disable

获取指令

iwpriv wlan1 get_mib disable_ch1213
wlan1 get_mib:1 0 0 0

设置指令

enable

iwpriv wlan1 set_mib disable_ch1213=1

ifconfig wlan1 down up

disable

iwpriv wlan1 set_mib disable_ch1213=0

ifconfig wlan1 down up

pa_type

支持8812不同的PA类型

0 – skyworth-5022

1 – RFMD-4501 / skyworth-85703

2 – SKYWORKS_5023

3 – RTC5634

16 – Internal PA

获取指令

iwpriv wlan0 get_mib pa_type

设置指令

iwpriv wlan0 set_mib pa_type=0

xcap

晶体电容值

0~62（0x3E）,0 表示未校准

获取指令

iwpriv wlan0 get_mib xcap
wlan0 get_mib:61 0 0 0
iwpriv wlan1 get_mib xcap
wlan1 get_mib:0 0 0 0

设置指令

iwpriv wlan1 set_mib xcap=61
iwpriv wlan1 get_mib xcap
wlan1 get_mib:61 0 0 0

备注：

一般都是生产写入，不要随便修改这个参数，可能会导致wifi连接不上

tssi1/tssi2

Tx 信号强度，tssi1表示Path A tssi2表示Path B，0~255,0表示未校准

获取指令

iwpriv wlan1 get_mib tssi1
wlan1 get_mib:0 0 0 0
iwpriv wlan1 get_mib tssi2
wlan1 get_mib:0 0 0 0
iwpriv wlan0 get_mib tssi1
wlan0 get_mib:0 0 0 0
iwpriv wlan0 get_mib tssi2
wlan0 get_mib:0 0 0 0

设置指令

iwpriv wlan1 set_mib tssi1=23
iwpriv wlan1 set_mib tssi2=23
iwpriv wlan0 set_mib tssi1=23
iwpriv wlan0 set_mib tssi2=23
iwpriv wlan0 get_mib tssi1
wlan0 get_mib:23 0 0 0
iwpriv wlan0 get_mib tssi2
wlan0 get_mib:23 0 0 0
iwpriv wlan1 get_mib tssi1
wlan1 get_mib:23 0 0 0
iwpriv wlan1 get_mib tssi2
wlan1 get_mib:23 0 0 0

ther

温度值，0表示未校准

范围：

For 8188C/8192C/8192D: 7 < ther <= 0x1d

Others: 7 < ther <= 0x32

获取指令

iwpriv wlan0 get_mib ther
wlan0 get_mib:30 0 0 0
iwpriv wlan1 get_mib ther
wlan1 get_mib:25 0 0 0

设置指令

iwpriv wlan0 set_mib ther=0x1e或者iwpriv wlan0 set_mib ther=30

iwpriv wlan1 set_mib ther=0x15或者iwpriv wlan1 set_mib ther=21

支持10进制和16进制设置

MIMO_TR_mode

MIMO模式分配

1 – 1T2R, 3 – 2T2R, 4 – 1T1R

获取指令

iwpriv wlan0 get_mib MIMO_TR_mode
wlan0 get_mib:3 0 0 0
iwpriv wlan1 get_mib MIMO_TR_mode
wlan1 get_mib:3 0 0 0

设置指令

iwpriv wlan0 set_mib MIMO_TR_mode=3
iwpriv wlan1 set_mib MIMO_TR_mode=3

tx2path

Enable tx using 2 path to send 1T rate

获取指令

iwpriv wlan0 get_mib tx2path
wlan0 get_mib:1 0 0 0
iwpriv wlan1 get_mib tx2path
wlan1 get_mib:1 0 0 0

设置指令

iwpriv wlan0 set_mib tx2path=1

iwpriv wlan1 set_mib tx2path=1

bcn2path

Enable 2 path to send beacon

获取指令

iwpriv wlan1 get_mib bcn2path
wlan1 get_mib:0
iwpriv wlan0 get_mib bcn2path
wlan0 get_mib:0

设置指令

iwpriv wlan0 set_mib bcn2path=1

iwpriv wlan1 set_mib bcn2path=1

acs_type

自动信道选择算法

0 – check numbers of APs to select a clear channel

1 – check numbers of APs, receiving traffic, false alarm counters to select a clear channel

获取指令

iwpriv wlan0 get_mib acs_type

iwpriv wlan1 get_mib acs_type

设置指令

iwpriv wlan0 set_mib acs_type=1

iwpriv wlan1 set_mib acs_type=0

add_cck1M_pwr

增加CCK 1M速率的功率值

0 – disable,

Other – the power added to CCK 1M in unit of power level

获取指令

iwpriv wlan0 get_mib add_cck1M_pwr
wlan0 get_mib:0

设置指令

iwpriv wlan0 set_mib add_cck1M_pwr=1

ssid

设置wifi SSID 最大32个字符

获取指令

iwpriv wlan0 get_mib ssid

设置指令

iwpriv wlan0 set_mib ssid="aaaa-test"

bcnint

设置beacon间隔单位ms,默认值100ms

范围20~1024

获取指令

iwpriv wlan0 get_mib bcnint
wlan0 get_mib:100 0 0 0
iwpriv wlan1 get_mib bcnint
wlan1 get_mib:100 0 0 0

设置指令

iwpriv wlan0 set_mib bcnint=200

dtimperiod

DTIM period

1~255,默认1

获取指令

iwpriv wlan0 get_mib dtimperiod
wlan0 get_mib:1 0 0 0
iwpriv wlan1 get_mib dtimperiod
wlan1 get_mib:1 0 0 0

设置指令

iwpriv wlan0 set_mib dtimperiod=2

iwpriv wlan1 set_mib dtimperiod=2

swcrypto

S/w encryption enabled/disabled

0 – disable, 1 – enable

获取指令

iwpriv wlan0 get_mib swcrypto

iwpriv wlan1 get_mib swcrypto

设置指令

iwpriv wlan0 set_mib swcrypto=1

iwpriv wlan1 set_mib swcrypto=1

aclmode/aclnum/acladdr

aclmode

Access control mode 0 – disable, 1 – accept, 2 – deny

aclnum

Set number of ACL Suggest set ‘0’ whenever driver is re-initialized

acladdr

Set access control address xxxxxxxxxxxx (12 digits mac address) When acl is added, the aclnum will be increased automatically

oprates

Operational rates

Bit0-bit11 for 1,2,5.5,11,6,9,12,18,24,,36,48,54 M

默认值0xfff

获取指令

iwpriv wlan1 get_mib oprates
wlan1 get_mib:255 15 0 0
iwpriv wlan0 get_mib oprates
wlan0 get_mib:240 15 0 0

设置指令

iwpriv wlan0 set_mib oprates=0xfff

iwpriv wlan1 set_mib oprates=0xfff

basicrates

Basic rates

Bit0-bit11 for 1,2,5.5,11,6,9,12,18,24,,36,48,54 M

默认值0xf

获取指令

iwpriv wlan0 get_mib basicrates
wlan0 get_mib:15 0 0 0
iwpriv wlan1 get_mib basicrates
wlan1 get_mib:15 0 0 0

设置指令

iwpriv wlan0 set_mib basicrates=0xf

iwpriv wlan1 set_mib basicrates=0xf

regdomain

Regulation domain

1-15 (FCC, IC, ETSI, SPAIN, FRANCE, MKK, ISREAL, MKK1, MKK2, MKK3, NCC, RUSSIAN, CN, GLOBAL, WORLD-WIDE)

获取指令

iwpriv wlan1 get_mib regdomain
wlan1 get_mib:3 0 0 0
iwpriv wlan0 get_mib regdomain
wlan0 get_mib:3 0 0 0

设置指令

iwpriv wlan0 set_mib regdomain=3

iwpriv wlan1 set_mib regdomain=3

txpwr_lmt_index

Set specific region domain for tx power limit

0 – use mib regdomain for tx power limit,

Other – the specific region domain index for tx power limit

获取指令

iwpriv wlan0 get_mib txpwr_lmt_index
wlan0 get_mib:0 0 0 0
iwpriv wlan1 get_mib txpwr_lmt_index
wlan1 get_mib:0 0 0 0

设置指令

iwpriv wlan0 set_mib txpwr_lmt_index=0

iwpriv wlan1 set_mib txpwr_lmt_index=0

autorate

Auto rate adaptive

获取指令

iwpriv wlan0 get_mib autorate
wlan0 get_mib:1 0 0 0
iwpriv wlan1 get_mib autorate
wlan1 get_mib:1 0 0 0

设置指令

iwpriv wlan0 set_mib autorate=1

iwpriv wlan1 set_mib autorate=1

txforce

设置固定TX速率为固定速率。
指令
iwpriv wlan0 set txforce=11
取值说明：0~11 for rate 1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48, 54M;
12~27 for rate MCS0, MCS1, …, MCS15；
这个命令设置完之后会立即生效，不需要对wlan0进行down up操作

fixrate

Fixed Tx rate,Refer when auto rate is disabled

Bit0-bit11 for 1,2,5.5,11,6,9,12,18,24,,36,48,54 M

Bit12-Bit27 for MCS0,MCS1,…,MCS15

(Bit31 + 0) for NSS1-MCS0

(Bit31 + 1) for NSS1-MCS1

(Bit31 + 2) for NSS1-MCS2…

(Bit31 + 10) for NSS2-MCS0

(Bit31 + 11) for NSS2-MCS1

(Bit31 + 12) for NSS2-MCS2

设置TX为固定速率。
iwpriv wlan0 set fixrate=0x08000000 //mcs15
这个命令设置完之后不会立即生效，需要对wlan0进行down up操作之后才能生效。另外设置fixrate之前需要使用iwpriv wlan0 set_mib autorate=0把autorate关闭。

获取指令

iwpriv wlan0 get_mib fixrate
wlan0 get_mib:0 0 0 0
iwpriv wlan1 get_mib fixrate
wlan1 get_mib:0 0 0 0

设置指令

iwpriv wlan0 set_mib fixrate=0xf

iwpriv wlan1 set_mib fixrate=0xf

disable_protection

orcedly disable protection mode

0 – auto, 1 – disable protection

Normally when 11g is used, driver will auto detect if legacy (11b) device is existed. When 11n is used, driver will auto detect if legacy (11b/g) device is existed. If yes, it will enable protection mode automatically.

获取指令

iwpriv wlan0 get_mib disable_protection
wlan0 get_mib:1 0 0 0
iwpriv wlan1 get_mib disable_protection
wlan1 get_mib:1 0 0 0

设置指令

iwpriv wlan0 set_mib disable_protection=1

iwpriv wlan1 set_mib disable_protection=1

disable_olbc

Forcedly OLBC detection

0 – auto, 1 – disable protection

Normally 11g AP should detect OLBC. If disabled, AP will enter protection mode only when legacy device associated.

deny_legacy

Deny the association from legacy STA for corresponding band

1 – 11b, 2 – 11g, 4 – 11a, 8 – 11n

Set the corresponding legacy band of STA to deny

prob_info_enable

Enable wlan driver to collect probe request information

0 – disable, 1 – enable

cat /proc/wlan0/probe_in fo to see the collect results

fast_roaming

Client mode fast roaming

0 – disable, 1 – enable

lowestMlcstRate

Use lowest basic rate to send multicast and broadcast

0 – disable Bit0-bit11 for 1,2,5.5,11,6,9,12,18,24,,36,48,54 M

Bit12-Bit27 for MCS0,MCS1,…,MCS15

stanum

Limit max associated sta number

0-32. 0 – disable (not limit).

获取指令

iwpriv wlan0 get_mib stanum

iwpriv wlan1 get_mib stanum

设置指令

iwpriv wlan0 set_mib stanum=16

802_1x

Flag of using 802.1x

0 disable 1 enable

When 802.1x is enabled, the Auth daemon must be invoked

获取指令

iwpriv wlan0 get_mib 802_1x

iwpriv wlan1 get_mib 802_1x

设置指令

iwpriv wlan0 set_mib 802_1x=0

hiddenAP

Hidden AP enable/disable

0 disabled 1 enabled

获取指令

iwpriv wlan0 get_mib hiddenAP
wlan0 get_mib:0 0 0 0
iwpriv wlan1 get_mib hiddenAP
wlan1 get_mib:0 0 0 0

设置指令

iwpriv wlan0 set_mib hiddenAP=1

iwpriv wlan1 set_mib hiddenAP=1

rtsthres/fragthres

rtsthres

RTS threshold

0-2347 default 2347

fragthres

Fragment threshold

256-2346 default 2346

shortretry/longretry

shortretry

Short retry limit 0-255

0 When set to 0, driver choose appropriate retry limit itself

longretry

Long retry limit 0-255 0 When set to 0, driver choose appropriate retry limit itself

expired_time

Client inactivity time in 10ms

>100 30000 Time unit is 10 ms.

获取指令

iwpriv wlan0 get_mib expired_time
wlan0 get_mib:48 117 0 0
iwpriv wlan1 get_mib expired_time
wlan1 get_mib:48 117 0 0

设置指令

iwpriv wlan0 set_mib expired_time=30000

block_relay

Block packet relaying between associated clients

0 – relay, 1 – block relay and drop, 2 – block relay and indicate to bridge

获取指令

iwpriv wlan0 get_mib block_relay
wlan0 get_mib:0 0 0 0
iwpriv wlan1 get_mib block_relay
wlan1 get_mib:0 0 0 0

设置指令

iwpriv wlan0 set_mib block_relay=1

iwpriv wlan1 set_mib block_relay=1

deny_any

Deny the association SSID of “any” including upper and lower cases

0 – disable, 1 – enable

crc_log

Calculate CRC error packets

0 – disable, 1 – enable

wifi_specific

Do WiFi logo test specific check

0 – disable, 1 – enable, 2 – auto 2

0 for performance mode;

1 for WiFi mode,

2 for auto mode.

PS. For 8192DR 1x1 concurrent mode and 8188E, please set 1 to pass WiFi logo test.

disable_txsc/disable_rxsc/disable_brsc

disable_txsc

Tx shortcut enable/disable

0 – enable, 1 – enable

disable_rxsc

Rx shortcut enable/disable

0 – enable, 1 – enable

disable_brsc

Bridge shortcut enable/disable

0 – enable, 1 – enable

band

Band selection

1 – 11b, 2 – 11g, 4 – 11a, 8 – 11n 64 – 11ac

vap_enable

Tell driver if multiple AP function is enabled or disabled

0 – disable, 1 – enable

If multiple AP is enabled, this mib must be set to 1.

func_off

Temporary disable wlan function

0 – normal, 1 – wlan off

Qos相关

qos_enable

Support WMM and QoS

0 – disable, 1 – enable

apsd_enable

Support WMM APSD function

0 – disable, 1 – enable

apsd_sta_be

Enable client mode BE queue

0 – disable, 1 – enable

This mid is only valid when apsd_enable is 1(enable)

apsd_sta_bk

Enable client mode BK queue

0 – disable, 1 – enable This mid is only valid when apsd_enable is 1(enable)

apsd_sta_vi

Enable client mode VI queue

0 – disable, 1 – enable

This mid is only valid when apsd_enable is 1(enable)

apsd_sta_vo

Enable client mode VO queue

0 – disable, 1 – enable

This mid is only valid when apsd_enable is 1(enable)

supportedmcs

Supported MCS rates Bit 0-15 for MCS0, …, MCS15

0xffff

basicmcs

Basic MCS rates Bit 0-15 for MCS0, …, MCS15

use40M

Support 40M bandwidth in 11n mode

0 – 20M 1 – 40M 2 -80M

2ndchoffset

Control sideband offset

1 – secondary channel is below the primary channel,

2 – secondary channel is above the primary channel 1

shortGI20M

Support short GI in 20M bandwidth

0 – disable, 1 – enable

shortGI40M

Support short GI in 40M bandwidth

0 – disable, 1 – enable

stbc

Support Space Time Block Coding

0 – disable, 1 – enable

ldpc

Enable ldpc

0 – disable, 1 – enable

ampdu

Support packet aggratation

0 – disable, 1 – enable

coexist

Support 20M/40M coexistant mode

0 – disable, 1 – enable

debug_err

Flag of DEBUG_ERR() macro

Bit value defined in 8185ag_debug.h (in hex) ffffffff

debug_info

Flag of DEBUG_INFO() macro

Bit value defined in 8185ag_debug.h (in hex) 0

debug_warn

Flag of DEBUG_WARN() macro

Bit value defined in 8185ag_debug.h (in hex) 0

debug_trace

Flag of DEBUG_TRACE() macro

Bit value defined in 8185ag_debug.h (in hex) 0

NUM_TX_DESC

8192cd_cfg.h
#define NUM_TX_DESC 2176 //512 // kmalloc max size issue

CE认证测试

2.4G

iwpriv wlan1 set_mib adaptivity_enable=1
iwpriv wlan1 set_mib manual_edca=1
iwpriv wlan1 set regdomain=13
Ifconfig wlan1 down up

5G

iwpriv wlan0 set_mib adaptivity_enable=1
iwpriv wlan0 set_mib manual_edca=1
iwpriv wlan0 set regdomain=13
Ifconfig wlan0 down up

开启dbg

echo dbg 0 1 > /proc/wlan0/cmd // dig odfm debug

修改dig

iwpriv wlan0 set_mib original_dig_restore=0

0 ：开启tdma_dig
1 ：关闭tdma_dig

使用iwpriv wlan0 set_mib rssi_dump=1可以看到输出

[1] 45% tx VHT NSS2 7s rx VHT NSS2 2 (ss 23 24) (FA CCK 0 0 OFDM 852 80)(CCA 2198 180)(LIG 0x2a,HIG 0x4e)(TP 0,0)

LIG：远距离

HIG:近距离

iwpriv wlan0 set_mib dig_enable=1// 关闭 DIG  
read DIG- 92Eiwpriv wlan0 read_reg b,c50siwpriv wlan0 read_reg b,c58- 8812ARiwpriv wlan0 read_reg b,c50iwpriv wlan0 read_reg b,e50- 8814ARiwpriv wlan0 read_reg b,c50iwpriv wlan0 read_reg b,e50iwpriv wlan0 read_reg b,1A50iwpriv wlan0 read_reg b,1850- write DIG- 89ESiwpriv wlan0 write_reg b,c50,20 - 92ESiwpriv wlan0 write_reg b,c50,20iwpriv wlan0 write_reg b,c58,20- 8812ARiwpriv wlan0 write_reg b,c50,2aiwpriv wlan0 write_reg b,e50,2a- 8814ARiwpriv wlan0 write_reg b,c50,30iwpriv wlan0 write_reg b,e50,30iwpriv wlan0 write_reg b,1A50,30iwpriv wlan0 write_reg b,1850,30   - DIG Related Registers- N-Series:Path-A IGI = RegC50[6:0]Path-B IGI = RegC58[6:0]CCK FA     = (RegA58[31:24]<<8) | RegA5C[7:0]OFDM FA    = RegCF0[15:0]RegCF0[31:16]RegDA0[31:16]RegDA4[15:0]RegDA4[31:16]RegDA8[15:0]- AC-Series:Path-A IGI = RegC50[6:0]Path-B IGI = RegE50[6:0]CCK FA     = RegA5C[15:0]OFDM FA    = RegF48[15:0]